Yanfeng Liu

As a hole-transport layer (HTL) material, poly(3,4-ethylenedioxythiophene):polystyrene-sulfonate (PEDOT:PSS) was often criticized for its intrinsic acidity and hygroscopic effect that would in the long run affect the stability of perovskite solar cells (Pero-SCs). As alternatives, herein water-soluble two-dimensional (2D) transition metal dichalcogenides (TMDs), such as MoS2 and WS2 were used as HTLs in p–i–n Pero-SCs. It was found that the content of 1T phase in 2D TMDs HTLs is centrally important to the power conversion efficiencies (PCEs) of Pero-SCs, and the 1T-rich TMDs (as achieved from exfoliation and without postheating) lead to much higher PCEs. More importantly, as PEDOT:PSS was replaced by 2D TMDs, both the PCEs and stability of Pero-SCs were significantly improved. The highest PCEs of 14.35 and 15.00% were obtained for the Pero-SCs with MoS2 and WS2, respectively, whereas the Pero-SCs with PEDOT:PSS showed a highest PCE of only 12.44%. These are up to date the highest PCEs using 2D TMDs as HTLs. After being stored in a glovebox for 56 days, PCEs of the Pero-SCs using MoS2 and WS2 HTLs remained 78 and 72%, respectively, whereas the PCEs of Pero-SCs with PEDOT:PSS almost dropped to 0 over 35 days. This study demonstrates that water-soluble 2D TMDs have great potential for application as new generation of HTLs aiming at high performance and long-term stable Pero-SCs.

s of 14.05 ± 0.21% in a ternary system (J71:ZITI-C:ZITI-N) that best optimize the balance between driving force and energy loss.

Organic photovoltaic cells (OPVs) have attracted broad attention and become a very energetic field after the emergence of nonfullerene acceptors. Long-lifetime triplet excitons are expected to be good candidates for efficiently harvesting a photocurrent. Parallel with the development of OPVs based on singlet materials (S-OPVs), the potential of triplet materials as photoactive layers has been explored. However, so far, OPVs employing triplet materials in a bulk heterojunction have not exhibited better performance than S-OPVs. Here, the recent progress of representative OPVs based on triplet materials (T-OPVs) is briefly summarized. Based on that, the performance limitations of T-OPVs are analyzed. The shortage of desired triplet materials with favorable optoelectronic properties for OPVs, the tradeoff between long lifetime and high binding energy of triplet excitons, as well as the low charge mobility in most triplet materials are crucial issues restraining the efficiencies of T-OPVs. To overcome these limitations, first, novel materials with desired optoelectronic properties are urgently demanded; second, systematic investigation on the contribution and dynamics of triplet excitons in T-OPVs is necessary; third, close multidisciplinary collaboration is required, as proved by the development of S-OPVs.

Non-fullerene acceptors with photoresponse beyond 1000 nm were synthesized with different thiophene bridges, which influence molecular orientation and thus device performance.

Abstract While photovoltaic blends based on non‐fullerene acceptors are touted for their thermal stability, this type of acceptor tends to crystallize, which can result in a gradual decrease in photovoltaic performance and affects the reproducibility of the devices. Two halogenated indacenodithienothiophene‐based acceptors that readily co‐crystallize upon mixing are studied, which indicates that the use of an acceptor mixture alone does not guarantee the formation of a disordered mixture. The addition of the donor polymer to the acceptor mixture readily suppresses the crystallization, which results in a fine‐grained ternary blend with nanometer‐sized domains that do not coarsen due to a high T g ≈ 200 °C. As a result, annealing at temperatures of up to 170 °C does not markedly affect the photovoltaic performance of ternary devices, in contrast to binary devices that suffer from acceptor crystallization in the active layer. The results indicate that the ternary approach enables the use of high‐temperature processing protocols, which are needed for upscaling and high‐throughput fabrication of organic solar cells. Further, ternary devices display a stable photovoltaic performance at 130 °C for at least 205 h, which indicates that the use of acceptor mixtures allows to fabricate devices with excellent thermal stability.