Keyou Yan

Cost-effective electrocatalysts for the oxygen evolution reaction (OER) are critical to energy conversion and storage processes. A novel strategy is used to synthesize a non-noble-metal-based electrocatalyst of the OER by finely combining layered FeNi double hydroxide that is catalytically active and electric conducting graphene sheets, taking advantage of the electrostatic attraction between the two positively charged nanosheets. The synergy between the catalytic activity of the double hydroxide and the enhanced electron transport arising from the graphene resulted in superior electrocatalytic properties of the FeNi-GO hybrids for the OER with overpotentials as low as 0.21 V, which was further reduced to 0.195 V after the reduction treatment. Moreover, the turnover frequency at the overpotential of 0.3 V has reached 1 s(-1), which is much higher than those previously reported for non-noble-metal-based electrocatalysts.

The precursor of solution-processed perovskite thin films is one of the most central components for high-efficiency perovskite solar cells. We first present the crucial colloidal chemistry visualization of the perovskite precursor solution based on analytical spectra and reveal that perovskite precursor solutions for solar cells are generally colloidal dispersions in a mother solution, with a colloidal size up to the mesoscale, rather than real solutions. The colloid is made of a soft coordination complex in the form of a lead polyhalide framework between organic and inorganic components and can be structurally tuned by the coordination degree, thereby primarily determining the basic film coverage and morphology of deposited thin films. By utilizing coordination engineering, particularly through employing additional methylammonium halide over the stoichiometric ratio for tuning the coordination degree and mode in the initial colloidal solution, along with a thermal leaching for the selective release of excess methylammonium halides, we achieved full and even coverage, the preferential orientation, and high purity of planar perovskite thin films. We have also identified that excess organic component can reduce the colloidal size of and tune the morphology of the coordination framework in relation to final perovskite grains and partial chlorine substitution can accelerate the crystalline nucleation process of perovskite. This work demonstrates the important fundamental chemistry of perovskite precursors and provides genuine guidelines for accurately controlling the high quality of hybrid perovskite thin films without any impurity, thereby delivering efficient planar perovskite solar cells with a power conversion efficiency as high as 17% without distinct hysteresis owing to the high quality of perovskite thin films.

Since the electrocatalytic activity of layered molybdenum disulfide (MoS2) for hydrogen evolution reaction (HER) closely depends on its exposed edges, the morphology and size of the material are critically important. Herein, we introduce a novel solvent-evaporation-assisted intercalation method to fabricate the hybrid of alternating MoS2 sheets and reduced graphene oxide layers, in which the nanosize of the MoS2 nanosheets can be effectively controlled by leveraging the confinement effect within the two-dimensional graphene layers. Significantly, the resulting MoS2/reduced graphene oxide (RGO) composite shows excellent catalytic activity for HER characterized by higher current densities and lower onset potentials than the conventional pre-exfoliated RGO supported MoS2 nanosheets. Further experiments on the effect of oxidation degree of graphene, the crystallinity of MoS2, and the exposed active site density on the HER performance of the MoS2/RGO composites show that there is an optimum condition for the catalytic activity of HER due to a balance between the numbers of exposed active sites of MoS2 and the internal conductive channels provided by graphene.

A planar perovskite solar cell that incorporates a nanocarbon hole-extraction layer is demonstrated for the first time by an inkjet printing technique with a precisely controlled pattern and interface. By designing the carbon plus CH3NH3I ink to transform PbI2 in situ to CH3NH3PbI3, an interpenetrating seamless interface between the CH3NH3PbI3 active layer and the carbon hole-extraction electrode was instantly constructed, with a markedly reduced charge recombination compared to that with the carbon ink alone. As a result, a considerably higher power conversion efficiency up to 11.60% was delivered by the corresponding solar cell. This method provides a major step towards the fabrication of low-cost, large-scale, metal-electrode-free but still highly efficient perovskite solar cells.

A novel organometal halide perovskite (CH3NH3PbI2Br) is synthesized and used as a visible light absorber to sensitize one-dimensional (1D) TiO2 nanowire arrays (NWAs) for all-solid-state hybrid solar cells. It achieved a power conversion efficiency (PCE) of 4.87% and an open circuit voltage (Voc) of 0.82 V, both higher than those of its analogue CH3NH3PbI3.